{"id":6867,"date":"2021-09-08T18:43:12","date_gmt":"2021-09-08T22:43:12","guid":{"rendered":"https:\/\/shootingsight.com\/?post_type=product&p=6867"},"modified":"2026-06-12T15:50:21","modified_gmt":"2026-06-12T19:50:21","slug":"509_striker","status":"publish","type":"product","link":"https:\/\/shootingsight.com\/?product=509_striker","title":{"rendered":"High performance Heavy Duty Striker for FNS \/ 509"},"content":{"rendered":"

High Performance, Heavy Duty Striker for FN FNS or 509 series pistols.\u00a0 Designed to be a trigger upgrade without having to replace the entire trigger system.<\/p>\n

There are two issues with the factory trigger: the gritty feel, and the reported failures due to it being a MIM part.\u00a0 Most of the grit has nothing to do with the trigger or linkage, but is the striker rubbing inside the unpolished slide channel as you pull through the first stage of the trigger pull, further is the sears sliding on each other, as you pull through the second stage.\u00a0 This High Performance striker is machined from billet 17\/4PH stainless steel, and is not simply a duplicate of the FN design, but has upgraded sear geometry, polished contact surfaces, a Teflon insert, and Nickel Boron low friction coating.\u00a0 The result is:<\/p>\n

    \n
  1. A much smoother trigger pull, due to Teflon bearing surface, and without having to polish or make any other permanent changes to your pistol.<\/li>\n
  2. Less creep in the second stage \u2013 30% reduction versus factory.<\/li>\n
  3. A sharper break \u2013 33% reduction versus factory.<\/li>\n
  4. A reduction in pull force, without light-weighting the springs, due to the low friction NiB coating, giving over 1lb reduction in pull versus factory.<\/li>\n
  5. A huge improvement in trigger performance WITHOUT having to replace the entire trigger assembly.\u00a0 This is a much cheaper option that delivers the benefits of a trigger job with only a few minutes to install, and no risk of damaging your frame by removing pins that the factory did not want removed.<\/li>\n<\/ol>\n

    The benefit of heavy duty comes from the fact that this is 17\/4PH Solid Billet Steel, rather than MIM.\u00a0 In MIM, you mix metal powder with a little bit of plastic, so when you heat it, you can pump it into a mold.\u00a0 When the plastic cools, it locks the metal in place.\u00a0 You then take that part and put it in a high temperature oven that burns out the plastic, and fuses the metal.\u00a0 This is a very inexpensive way to make parts that would be difficult to machine.\u00a0 Problem is that if the metal powder is not evenly distributed, or has clumps, you can end up with micro-voids inside your finished part, that can act as stress concentrators or crack initiation sites.\u00a0 Further, since you are spending money for every bit of metal you add, the lowest cost option has the least amount of material.\u00a0 Billet, on the other hand, is solid.\u00a0 The hot roll process to produce it kneads the steel so it is almost impossible to get an internal void.\u00a0 Further, since you are starting with solid, you are spending money to remove metal, so the lowest cost option has the MOST amount of metal in the part, and is thus likely more robust.<\/p>\n

    In short, this striker is a heavy duty drop-in trigger job, without having to do a complete disassembly of the lower.\u00a0 It is a single part, switched out in the slide in under 5 minutes.\u00a0 The attached pull force chart shows the benefits in creep, sharpness of break, and reduction of pull force:<\/p>\n

    \u00a0<\/p>\n

    \"\"<\/p>\n

    \u00a0<\/p>\n

    \u00a0<\/p>\n","protected":false},"excerpt":{"rendered":"

    High Performance striker for FN FNS \/ 509 pistol.<\/p>\n

    A trigger upgrade, without having to disassemble the trigger.<\/p>\n